Changes for the WTN Family

V 23.33 2023-03-07
	New rs485 command to trigger a trigger

V 22.81 2022-08-30
	Added baudrate parameter in RemotRFUpdate command

V 22.71 2022-07-15
	Bugfix for SJS2-WTN: Memory optimized

V 22.32 2022-03-07
	Support for WTN2 system

V 22.21 2022-02-02
	Bugfix for enumeration handling for SJS2

V 21.91 2021-09-21
	Bugfinx in OPTIc3 trigger handling

V 21.71 2021-07-23
   internal version

V 20.11	2020-01-24
    Trigger handling for BANG2 improved
	
V 19.91	2019-09-25
	The CKN's serial interface uses no more a delimiter and creates 64 Byte packets
	Implementation of the BANG2 firmware
	Internal version
	
V 18.C1 2018-12-19
    CKN changes at startup always to 9600 Baud as display board baudrate
	
V 18.B1 2018-11-20
	Don't forward serial data from netork, when an firmware update (via RF or serial) is in progress

V 18.82 2018-08-31
	Improvements in SJS2 and SJC2 firmware

V 18.62 2018-06-27
	Support of SJS2 and SJC2
	Secure data transmission on RS232 re-activated
	unused testmode of Timy3W WTN device removed
	
V 18.21 2018-02-02
    Bang at 2-Edge mode worked only every 30 seconds, False start was not possible. Solved.
	In very rare cases it could happen that the WTN module crashed at start-up. So the socket enumeration get lost. Solved.

V 17.B1 2017-10-02
    Unofficial Version
    e-StartW: At power on it could be an impulse. Solved.

V 17.61 2017-06-22
    Bang: Timing channel is now always output

V 17.51 2017-05-15
    RF update was not possible for OPTIc3

V 17.31 2017-03-16
	Bug fix for bang: Works now correct in 2edge-mode.

V 16.C5 2016-12-20
    Voting Terminal improved
	New command to disable Hardware impulses.
	Data transmission RS232: Data could get lost in some cases
	Save data transmission of logical level at 2-edge mode (for OPTIc3)

V 15.71 2015-07-03
    Delayed Times of e-StartW are marked to calculate the correct delay.
    If a WTN-PB or e-StartW is set to default values, also the used Standard Channel will be set to the standard delay time of 0,1s.
    
V 15.31 2015-02-13
    Battery type was not always displayed correctly.

V 15.22 2015-02-13
    Problems with GAZ data in V 15.21 Solved.

V 15.21 2015-02-09
    Now all channels can be used for enumerating the socket mode.
    After a update the GAZ interface was deactivated.
    The serial interface can be switched now for socket mode.
    GAZ Interface did not work with socket mode.
        
V 14.B1 2014-11-06
    Internal version for Production

V 14.A2 2014-10-30
    At a Timeserver restart the first impulse was missing. Solved.

V 14.A1 2014-10-22
    Correct display in Timy3 of old Versions in the network.
    Problem with timeserver change solved: It could happen that several times were transmitte in this case.
    Delay time at WTN-PB, e-Start and Pr1aW corrected. (delay time of C0 was always used)

V 14.71 2014-07-14
    Small changes for WTN-PB
    Small changes on synchronization and update behavior.

V 14.51 2014-05-22
   Wrong behavior at RF Update solved
   Error in Bootloader solved
   Corrections for WTN-PB
   Delaytime can't be set to 0 (wrong) anymore.
   Improvements for voting terminal

V 14.42 2014-04-22
    "WTN-PB"
        Sending of trigger in configuration mode
        Exceeding C4 starts at C0 again
    Delay time can't be set to 0
    Wrong behavior at RF-Update corrected.

V 14.41 2014-04-08
    Timing Channel can be set up now at WTN-PB via Software.
    Timing of RS485 improved
    No more Red LED blinking on PR1aW and WTN-PB on remote commands
    Implementation voting terminal

V 14.31 2014-03-05
    First Implementation of new Device WTN-PB
    RF Update starts only if minimum one neighbour is present

V 14.22  2014-02-21
    Voting Terminal support improved
    Signalling of LED from PR1aW and WTN-DB device improved
    
V 14.21  2014-02-13 internal test version
    PR1aW shows now RSSI Values with the LED: green=good reception, orange=moderate reception; red=poor reception; off=no network
    Voting Terminal support added
    "Pulse Hold" message could stop: solved
    Some stability improvements
    
V 13.C3  2013-12-27
    Avoid of wrong Pulse Hold Messages
    Optimizing of long distance WTN chains

V 13.C1  2013-12-10
    Pulse Hold works now also with other Channels than C0 on PR1aW 

V 13.B4  2013-11-29
    New device "Bang"

V 13.B3  2013-11-26
    Internal release
    
V 13.B2  2013-11-25
    behavior changed if time server is restarted
    New device "Bang"

V 13.B1  2013-11-19
    New boot loader prevent from destroying the device while updating and power loss - only for new devices.

V 13.A2  2013-10-30
    Small bug fixes
    
V 13.A1  2013-10-04
    Version display changed for Timy3
    Binary data transmission for CKN
    Reset-behavior changed for new bootloader
    
V 13.92  2013-09-19
    Some small improvements
    Resends depending on amount of neighbours
    Pulse hold is shown as "P"
    Unneeded RS485 menu removed
   
V 13.82  2013-08-22
    New Menu for RS485 Baud rate:
      Please set this only for WTN-WS to 4800 Baud.
    WTN<->WTN-WS Communication works now.

V 13.74  2013-07-26
    Pulse hold support improved.
    WTN-WS: RS485 Baud rate isn't changed anymore.

V 13.71  2013-07-05
    WTN-DB: Red LED when no other partner connected.
    Pulse Hold improved to 2-edge mode.
    PR1aW: Test mode was not shown properly anymore.
    Info Display shows now also shorter GAZ Data strings.
    When there were two or more GAZ display boards connected the data were not shown properly. now solved.

V 13.63  2013-06-28
    Version output GAZ interface on WTN-DB.
    Some improvements.

V 13.62  2013-06-26
    First implementation of "Pulse hold" Function: Message about permanent channel triggering.
    Compiler change.
    
V 13.61  2013-06-16
    GAZ Data transmission did not work properly on new WTN Hardware and WTN-DB.
    Improvement of RF Update procedure. Missing packets a now re-requested.
    internal improvements.

V 13.51  2013-05-22
    PC Update changes the Baud rate of RS232 to 9600 Baud.
    Display of "V" in the status screen if different Software Versions on the same network.
    
V 13.42  2013-04-04
    RSSI: CM is displayed if devices with software versions prior 13.33 are in the Network.
    RS485 Commands added.
    A "V" is shown if devices with different software versions are in the Network
    Synchronisation improved.    .
    
V 13.41  2013-04-02
    PR1aW crashed on a RF update. Now solved
    RS483 Command set improved
    Display of "V" if different Software versions in the WTN Network.
    Display of "R" on RS485 command    
    Bug fix for GAZ WTN on RS485 data
    Timesync-Problem with compatibility mode solved    

V 13.33  2013-03-15
    RS 232 interface improved and some Bugs fixed.
    GAZ data transmission improved and some Bugs fixed.
    Synchronization improved.
    Networking improved.
    A wrong Measurement switched the WTN off at Temperatures below -25 Degrees. Solved.
    Firmware RF update was not possible if GAZ Data was sent.
     This data is now switched off during an update.
    Firmware RF update did not work with 3+ active devices.
    Transmission protocol improved. 
     This new protocol gets active when all devices in the Network have the latest Software.